Top 8 Arduino Motor Shield UK – Motherboards

As an Amazon Associate I earn from qualifying purchases.

1. diymore

#ad

Diymore L298P Shield Expansion Board DC Motor Driver Module 2A H-Bridge 2 way Compatible with UNO-R3 Mega-2560

#ad
diymore #ad - Motor controller l298p, Drives 2 DC motors or 1 stepper motor. Max current 2a per channel or 4A max with external power supply. You can also measure the motor current absorption of each motor, among other features. The l298p expansion board lets you drive two DC motors with your board, controlling the speed and direction of each one independently. The motor shield is based on the l298, solenoids, which is a dual full-bridge driver designed to drive inductive loads such as relays, DC and stepping motors.
Branddiymore #ad
Manufacturerdiymore #ad
Part NumberD010396
Model2698692

2. DAOKAI

#ad

DAOKAI CP2102 Development Board WiFi Module + L293D WiFi Motor Drive Expansion Board ESP8266 Motor Expansion Board Shield Module for Arduino MCU Development Kit

#ad
DAOKAI #ad - Module adopts fold plug-in circuit board design, can be directly access ESP12E Dev Kit or for module. Circuit diagram layout is reasonable, SMD encapsulation, installation is very convenient. Easy to usedc motor can be driven directly 2 road or road 1 stepper motor, drive current biggest can reach 1.

2 a. Describeesp12e motor shields is a compatible esp12e dev kit and for a large current Motor driver module. Pin functionlead out all functional pins of esp12 dev kit: spi, ai and 3. 3v power interface, uart, can directly drive two-way motor, Motor power supply range: 4.5v~36v, expand two-way motor drive, onboard power switch, GPIO, control power supply range: 4.5

5v~9v. Package includesyou will get 1 x l293d wifi motor drive expansion boardboard, 2 x 50cm/19. 68inch 24awg cable, 1 x esp8266 esp-12e development Board, 1 x 30cm/12inch Micro USB data cable. Button designmodule uses the humanized design, use the power button switch, users can conveniently on the power switch. Simple and easy to use.
BrandDAOKAI #ad
ManufacturerDAOKAI #ad
Part NumberWE-DA-158
ModelWE-DA-158

3. Switch Electronics

#ad

L293D Motor Drive Shield Expansion Board Compatible with Arduino Mega UNO R3 Microcontrollers

#ad
Switch Electronics #ad - Input voltage of 4. 5v to 16V. Module also features 4 h bridges, capable of supplying 600mA per channel in either direction to an input. L293d motor drive shield, monolithic 4 channel driver suitable for use with power supplies and DC motors up to 36VDC. Can drive up to 4 dc motors, 2 stepper motors or 2 servos. Pins designed to be compatible with Arduino, Uno, Mega and other Microcontrollers.
BrandSwitch Electronics #ad
ManufacturerSwitch Electronics #ad
Part Number483147

4. Youmile

#ad

Youmile 5-Pack Dual H Bridge DC Stepper Motor Drive Controller Board Module L298N for arduino

#ad
Youmile #ad - The signal is shown in the figure. The connecting method is shown inbelow figure after enable ENA ENB. Driving dc motor because the module is drived by double H bridge, it can drive two motors simultaneously. Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled.
BrandYoumile #ad
ManufacturerYoumile #ad
Part NumberTS-YM-078
ModelTS-YM-078

5. UMTMedia

#ad

UMTMedia® L293D Motor Drive Shield Expansion Board For Arduino Duemilanove Mega UNO

#ad
UMTMedia #ad - Multifunction, easy to operate, with powerful driver library support and feature updates. 2-pin terminal block to connect external power, for seperate logic/motor supplies. Pull down resistors keep motors disabled during power-up. Big terminal block connectors to easily hook up wires 10-22AWG and power. Arduino reset button brought up top.
BrandUMTMedia #ad
ManufacturerUMTMedia® #ad

6. KEYESTUDIO

#ad

Compatible for Arduino Leonardo, UN0, Mega, KEYESTUDIO CAN-Bus Shield for Arduino

#ad
KEYESTUDIO #ad - The resistance of terminal resistor should be as same as communication cable. The onboard bus control chip can realize the data control on the CAN bus and data communication between devices. Keyestudio can-bus shield shield provides a db9 connector, and provide various interfaces, I2C, connector, etc.

So you can choose the interface according to your needs. It also comes with microsd card slot, such as uart, so you can directly insert MicroSD card to store data. Notice: the two ends of can buscan-h and can-l must be connected to terminal resistor so that CAN BUS can work normally. Additionally, it can match bus resistance to strengthen the anti-interference and reliability of data communication. Keyestudio can-bus shield support ①standard frame, extended frame of transmission and reception; ②support two receiving methods: Polling and interrupt;③support SD card data storage;④support power supply via Arduino motherboard or DB9 connector.

Its typical value is 120 ohms. Keyestudio can-bus shield is particularly designed for arduino controllers. Compatible with the arduino uno standard interface; can be perfectly adapted to the main control boards such as Arduino UNO and Arduino Leonardo.
BrandKEYESTUDIO #ad
Manufacturerkeyes #ad
Height1.1
Length2.6
Width2.13
Modelcan-bus
Warranty3 months

7. Arduino

#ad

Arduino Uno REV3 A000066

#ad
Arduino #ad - Uno" means one in italian and was chosen to mark the release of Arduino Software IDE 1. 0, now evolved to newer releases. Arduino is an open-source hardware, software, and content platform with a worldwide community of over 30 million active users.

It has 14 digital input/output pins of which 6 can be used as PWM outputs, a power jack, a 16 MHz quartz crystal, 6 analog inputs, a USB connection, an ICSP header and a reset button. This board is your entry to the unique Arduino experience: great for learning the basics of how sensors and actuators work, and an essential tool for your rapid prototyping needs. Arduino uno is the most used and documented board in the world.
BrandArduino #ad
ManufacturerArduino #ad
Height2.49 cm (0.98 Inches)
Length8 cm (3.15 Inches)
Weight0.05 kg (0.1 Pounds)
Width5.51 cm (2.17 Inches)
Part NumberA000066
ModelA000066
Warranty1 YearManufacturer Guarantee

8. AptoFun

#ad

AptoFun 16x2 LCD Keypad Shield For Arduino UNO, MEGA R3, Mega2560 Duemilanove

#ad
AptoFun #ad - Lcd 1602 keypad shield displays 16 x 2 characters with background lighting and contrast setting. Easy to connect with arduino Duemilanove. Module weight: 57g. 4 directional buttons, a selection button and a reset button simplify the Arduino application.
BrandAptoFun #ad
ManufacturerAptotec #ad
Height2 cm (0.79 Inches)
Length8 cm (3.15 Inches)
Weight57
Width5.8 cm (2.28 Inches)
Part NumberB01BI6UKHW
ModelB01BI6UKHW